mad00017hem mn101c66d, mn101c66g type mn101c66d mn101c66g mn101cf66g MN101CP66D internal rom type mask rom flash eprom rom (byte) 64k 128k 64k ram (byte) 2k 4k 2k package (lead-free) lqfp080-p-1414a, qfp084-p-1818e lqfp080-p-1414 a (es (engineering sample) available), qfp084-p-1818e lqfp080-p-1414a, qfp084-p-1818e minimum instruction execution time 0.1 s (at 4.5 v to 5.5 v, 20 mhz) 0.25 s (at 2.7 v to 5.5 v, 8 mhz) 62.5 s (at 2.0 v to 5.5 v, 32 khz) * * the lower limit for operation guarantee for ? ash memory built-in type is 2.5 v. * the lower limit for operation guarantee for eprom built-in type is 2.3 v. ? interrupts reset, watchdog, external 0 to 2 , external 3 (lqfp 080 -p- 1414 a : not mounted), external 4 (key interrupt dedicated), timer 0 to 3 , timer 6 , timer 7 (2 systems), timer 8 (2 systems), time base, serial 0 (2 systems), serial 2 , a/d conversion ? nish ? timer counter timer counter 0 : 8-bit 1 (square-wave/ 8-bit pwm output, event count, generation of remote control carrier , simple pulse width measurement) (square-wave/pwm output to large current terminal p 50 possible) clock source ................ 1/2, 1/4 of system clock frequency; 1/1, 1/4, 1/16, 1/32, 1/64 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency; external clock input interrupt source ........... coincidence with compare register 0 timer counter 1 : 8-bit 1 (square-wave output, event count, synchronous output event) clock source ................ 1/2, 1/8 of system clock frequency; 1/1, 1/4, 1/16, 1/8192, 1/32768 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency; external clock input interrupt source ........... coincidence with compare register 1 timer counter 0, 1 can be cascade-connected. timer counter 2 : 8-bit 1 (square-wave output, additional pulse type 10-bit pwm output, event count, synchronous output event, simple pulse width measurement) (square-wave/pwm output to large current terminal p 52 possible) clock source ................ 1/2, 1/4 of system clock frequency; 1/1, 1/4, 1/16, 1/32, 1/64 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency; external clock input interrupt source ........... coincidence with compare register 2 timer counter 3 : 8-bit 1 (square-wave output, event count, generation of remote control carrier, serial 0 baud rate timer) clock source ................ 1/2, 1/8 of system clock frequency; 1/1, 1/4, 1/16, 1/64, 1/128 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency; external clock input interrupt source ........... coincidence with compare register 3 timer counter 2, 3 can be cascade-connected. timer counter 6 : 8-bit freerun timer clock source ................ 1/1 of system clock frequency; 1/1, 1/4096, 1/8192 of osc oscillation clock frequency; 1/1, 1/4096, 1/8192 of xi oscillation clock frequency interrupt source ........... coincidence with compare register 6 timer counter 7 : 16-bit 1 (square-wave output, igbt/ 16-bit pwm output (cycle / duty continuous variable), event count, synchronous output evevt, pulse width measurement, input capture) (square-wave/pwm output to large current terminal p 51 possible) clock source ................ 1/1, 1/2, 1/4, 1/16 of system clock frequency; 1/1, 1/2, 1/4, 1/16 of osc oscillation clock frequency; 1/1, 1/2, 1/4, 1/16 of external clock input frequency interrupt source ........... coincidence with compare register 7 (2 lines)
mad00017hem mn101c66d, mn101c66g timer counter 8 : 16 bit 1 (square-wave/ 16-bit pwm output [duty continuous variable], event count, pulse width measurement, inputcapture) (square-wave/pwm output to large current terminal p 53 possible) clock source ................ 1/1, 1/2, 1/4, 1/16, 1/128 of system clock frequency; 1/1, 1/2, 1/4, 1/16, 1/128 of osc oscillation clock frequency; 1/1, 1/2, 1/4, 1/16 of external clock input frequency interrupt source ........... coincidence with compare register 8 (2 lines) timer counters 7, 8 can be cascade-connected. (square-wave output, pwm, input capture, pulse width measurement is possible as a 32 -bit timer.) time base timer (one-minute count setting) clock source ................ 1/1 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency interrupt source ........... 1/128, 1/256, 1/512, 1/1024, 1/8192, 1/32768 of clock source frequency watchdog timer interrupt source ........... 1/65536, 1/262144, 1/1048576 of system clock frequency ? serial interface serial 0 : synchronous type/uart (full-duplex) 1 clock source ................ 1/2, 1/ 4 of system clock frequency; pulse output of timer counter 3; 1/2, 1/ 4, 1/16, 1/ 64 of osc oscillation clock frequency serial 2 : synchronous type 1 clock source ................ 1/2, 1/ 4 of system clock frequency; pulse output of timer counter 3; 1/2, 1/ 4, 1/16, 1/ 32 of osc oscillation clock frequency ? i/o pins i/o 61 (60) common use , speci? ed pull-up resistor available, input/output selectable (bit unit) ( ) : lqfp080-p-1414a input 4 (3) common use , speci? ed pull-up resistor available ( ) : lqfp080-p-1414a ? a/d converter 10-bit 8 -ch. (with s/h) ? display control function lcd 32 segments 4 commons (static, 1/2, 1/3, or 1/4 duty) lcd power supply separated from vdd (usable if vlcd vdd) lcd power shunt resistance contained ? special ports buzzer output, remote control carrier signal output, high-current drive port ? electrical charactreistics (supply current) parameter symbol condition limit unit min typ max operating supply current idd1 fosc = 20 mhz , vdd = 5 v 25 60 ma idd2 fosc = 8 mhz , vdd = 5 v 10 25 ma idd3 fx = 32 khz , vdd = 3 v 30 100 a supply current at halt idd4 fx = 32 khz , vdd = 3 v, ta = 25 c 4 8 a idd5 fx = 32 khz , vdd = 3 v , ta = C40 c to +85 c 30 a supply current at stop idd6 vdd = 5 v , ta = 25 c 2 a idd7 vdd = 5 v , ta = C40 c to +85 c 50 a ? development tools in-circuit emulator px-ice 101c/d+px-prb101c66-qfp084-p-1818e-m px-ice101c/d+px-prb101c66-lqfp080-p-1414a-m
mad00017hem ? pin assignment 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 1 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 vlc1 vlc2 vlc3 c1 c2 tm7o, led1, p51 tm2o, led2, p52 tm8o, led3, p53 vss osc2 osc1 mmo d xi xo vdd nrst , p27 vref+ an0, pa 0 an1, pa 1 an2, pa 2 tm8io, p15 tm7io, p14 tm3io, p13 tm2io, p12 tm1io, p1 1 rmout , tm0io, p10 buzzer, p06 sbt2, p05 sbi2, p04 sbo2, p03 sbt0, p02 rxd, sbi0, p01 txd, sbo0, p00 vdd vref- an7, pa 7 an6, pa 6 an5, pa 5 an4, pa 4 an3, pa 3 p67, seg16 p66, seg17 p65, seg18 p64, seg19 p63, seg20 p62, seg21 p61, seg22 p60, seg23 p47, key7, seg24, sdo7 p46, key6, seg25, sdo6 p45, key5, seg26, sdo5 p44, key4, seg27, sdo4 p43, key3, seg28, sdo3 p42, key2, seg29, sdo2 p41, key1, seg30, sdo1 p40, key0, seg31, sdo0 vdd p22, irq2 p21, irq1, acz p20, irq0 p70, seg15 p71, seg14 p72, seg13 p73, seg12 p74, seg1 1 p75, seg10 p76, seg9 p77, seg8 p80, seg7 p81, seg6 p82, seg5 p83, seg4 p84, seg3 p85, seg2 p86, seg1 p87, seg0 com0, p30 com1, p31 com2, p32 com3, p33 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 mn101c66d mn101c66g lqfp080-p-1414a
mad00017hem mn101c66d, mn101c66g ? pin assignment mn101c66d mn101c66g qfp084-p-1818e 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 1 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 vlc1 vlc2 vlc3 n.c n.c tm0o, led0, p50 tm7o, led1, p51 tm2o, led2, p52 tm8o, led3, p53 na trst vss osc2 osc1 mmo d xi xo vdd nrst , p27 vref+ an0, pa 0 an1, pa 1 tm8io, p15 tm7io, p14 tm3io, p13 tm2io, p12 tm1io, p1 1 rmout , tm0io, p10 buzzer, p06 sbt2, p05 sbi2, p04 sbo2, p03 sbt0, p02 rxd, sbi0, p01 txd, sbo0, p00 vdd vref- an7, pa 7 an6, pa 6 an5, pa 5 an4, pa 4 an3, pa 3 an2, pa 2 p67, seg16 p66, seg17 p65, seg18 p64, seg19 p63, seg20 p62, seg21 p61, seg22 p60, seg23 p47, key7, seg24, sdo7 p46, key6, seg25, sdo6 p45, key5, seg26, sdo5 p44, key4, seg27, sdo4 p43, key3, seg28, sdo3 p42, key2, seg29, sdo2 p41, key1, seg30, sdo1 p40, key0, seg31, sdo0 vdd p23, irq3 p22, irq2 p21, irq1, acz p20, irq0 p70, seg15 p71, seg14 p72, seg13 p73, seg12 p74, seg1 1 p75, seg10 p76, seg9 p77, seg8 p80, seg7 p81, seg6 p82, seg5 p83, seg4 p84, seg3 p85, seg2 p86, seg1 p87, seg0 n.c. com0, p30 com1, p31 com2, p32 com3, p33
request for your special attention and precautions in using the technical information and semiconductors described in this book (1) if any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and regulations of the exporting country, especially, those with regard to security export control, must be observed. (2) the technical information described in this book is intended only to show the main characteristics and application circuit examples of the products, and no license is granted under any intellectual property right or other right owned by our company or any other company. therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other company which may arise as a result of the use of technical information described in this book. (3) the products described in this book are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). consult our sales staff in advance for information on the following applications: ? special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the prod- ucts may directly jeopardize life or harm the human body. ? any applications other than the standard applications intended. (4) the products and product specifications described in this book are subject to change without notice for modification and/or im- provement. at the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date product standards in advance to make sure that the latest specifications satisfy your requirements. (5) when designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions (operating power supply voltage and operating environment etc.). especially, please be careful not to exceed the range of absolute maximum rating on the transient state, such as power-on, power-off and mode-switching. otherwise, we will not be liable for any defect which may arise later in your equipment. even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (6) comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (esd, eos, thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. when using products for which damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages. (7) this book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of matsushita electric industrial co., ltd. industrial co., ltd.
|
